Вести
How to solve the problem of power module selection
Автор: ZYG Power Module Time： 2022-12-20
It is not easy to select a power module. There are many difficulties to consider. How much do you know?
Magnetic beads, capacitors, diodes, resistors… all have similar inside stories, but people don’t pay much attention to them. There are various topologies of power modules, such as flyback, forward, push-pull, half-bridge, and full-bridge. Due to their different basic principles, each of them is mainly manifested in the advantages at the level of certain characteristic indicators.
The flyback power supply does not have a time period for charging and discharging the battery during the power switch period. That is because there is no time characteristic of the response characteristic, and the grain baud cannot be guaranteed to be very good, although it may not help much according to the energy storage capacitor , but the rationale is just a flaw.
Leakage inductance is also a big problem, but its advantages are simple power supply circuit, low cost, light weight, no need to add magnetic calibration windings, and a wider operating voltage range for typing. Because of this, its share of the total power supply sales market is about 7%.
The output voltage of the positive power supply has good transient operation characteristics and strong load capacity, but its disadvantages are also obvious. The large energy storage technology is used to filter the inductor and the freewheeling diode, which is large in size, and the back electromotive force of the primary coil of the transformer is high. .
The push-pull power supply has high transient response time, good working voltage and frequency characteristics. It is the most utilized power transformer of all topologies. No flux leakage, simple optocoupler circuit.
If the two forward converters are not completely symmetrical or balanced, the bias magnetism accumulated after many cycles will cause the magnetic core to enter a saturated state, resulting in excessive excitation current of the high-frequency transformer, and even damage the power switch tube.
The accumulative chainless power supply transformer has a large power and high working efficiency, the withstand voltage test value of the power switch tube is relatively low, and the primary coil of the transformer only needs to be wound once. The disadvantage is that the efficiency is low, there is a semiconductor area, and the consumption is large.
The above problems are all caused by the inherent advantages and disadvantages of its topology. Although people can use the power module as the black box of the aircraft, this is also a point that needs to be paid attention to when choosing a power supply.
Претходно: How to choose a power module and precautions, each is very important
Следно: The Importance of Quality Control in China DC-DC Converter Manufacturing
релевантни информации
-
2023-6-12
Power Up with the HP Series AC-DC Converter
In today's digital age, there is a growing need for reliable and efficient power sources to keep electronic devices running smoothly. The HP Series AC-DC converter is a cutting-edge power solution that is designed to meet the power needs of a wide range of electronic devices. This article will explore the features and benefits of the HP Series AC-DC converter, as well as its applications in various industries. Features of the HP Series AC-DC Converter The HP Series AC-DC converter is a high-performance power supply that is designed to provide a stable and reliable power source for electronic devices. Some of the key features of this converter include: 1. High Efficiency: The HP Series AC-DC converter is highly efficient, with...
Погледнете детали -
2023-5-5
AC-DC Power Supply: A Complete Guide
AC-DC power supply is a device that converts alternating current (AC) to direct current (DC) for use by electronic devices. The output voltage and current of a power supply can be regulated to meet the requirements of different electronic devices. In this guide, we will discuss the different types of AC-DC power supplies, their applications, and how to select the right power supply for your needs. Types of AC-DC Power Supplies There are two basic types of AC-DC power supplies: linear and switching. Linear power supplies use a transformer to convert AC input voltage to a lower AC voltage, which is then rectified and regulated to produce a DC output voltage. Switching power supplies use high-frequency switching to convert AC...
Погледнете детали -
2023-5-12
24V AC to DC Converter: Converting Alternating to Direct Current
Introduction In today's world, electricity is an integral part of our daily lives. It powers almost everything we use, from the lights in our homes to the computers we work on. However, the electricity we use is not always in a form that we can use. Alternating current (AC) is the form of electricity that is typically supplied by power companies, while most of our devices and appliances require direct current (DC) to operate. This is where a 24V AC to DC converter comes in handy. What is a 24V AC to DC Converter? A 24V AC to DC converter is a device that converts alternating current (AC) into direct current (DC). It takes in AC power and outputs DC...
Погледнете детали -
2023-4-28
Design of an AC-DC Converter Circuit
An AC-DC converter circuit is a device that converts alternating current (AC) to direct current (DC). It is an essential component of many electronic devices, including power supplies, computers, and telecommunications equipment.The design of an AC-DC converter circuit involves several key components, including a transformer, rectifier, filter, and voltage regulator. These components work together to convert the AC input voltage into a stable DC output voltage that can be used to power electronic devices.The transformer is the first component in the AC-DC converter circuit. It is used to step down the high voltage AC input to a lower voltage that can be rectified and filtered. The transformer consists of two coils of wire wound around a magnetic core. The primary...
Погледнете детали -
2023-6-24
Bidirectional DC DC Converter: Principles, Topologies, and Applications
A bidirectional DC-DC converter is a power electronic device that can transfer electrical energy bidirectionally between two DC voltage levels. It is widely used in various applications, including electric vehicles, renewable energy systems, and battery energy storage systems. This article will explore the principles, topologies, and applications of bidirectional DC-DC converters. Principles of Bidirectional DC-DC Converter The main function of a bidirectional DC-DC converter is to transfer power from one DC voltage level to another. The power transfer can be either unidirectional or bidirectional. A bidirectional converter can transfer energy from a high voltage source to a low voltage load and vice versa. Bidirectional DC-DC converters typically consist of two power converters, each with its own power switch and control...
Погледнете детали -
2023-7-9
Introducing the Advanced DC DC Converter EX Series
In the ever-evolving world of electronics, the demand for efficient power conversion solutions continues to rise. Companies are constantly looking for advanced technologies that can provide reliable and high-performance power conversion in a compact form factor. And that is where the Advanced DC DC Converter EX Series comes in. The Advanced DC DC Converter EX Series is a groundbreaking lineup of power converters designed to meet the diverse needs of various industries. With cutting-edge technology and innovative design, this series offers unparalleled performance and flexibility. One of the key features of the Advanced DC DC Converter EX Series is its high efficiency. These converters boast an efficiency of up to 95%, ensuring minimal power loss and maximum energy utilization. This...
Погледнете детали