nouvelles
À propos de l'importance, de la structure et de la manière de choisir le module d'alimentation DC-DC ?
Auteur： Module d'alimentation ZYG Time： 2022-4-7
With the development of the times, electronic products are more and more developed, DC-DC power modules are widely used in today’s society, and some electrical appliances used in daily life are also applied to them. Do you understand the importance and structure of DC-DC power modules? Know why you should choose a DC-DC power module? Today I will take you to find out.
The importance of DC-DC power module:
DC-DC power module is a compact, high quality regulated power supply products, using advanced manufacturing technology. Because the module power supply is simple to use, it has the advantages of convenient expansion and good maintainability when composing the system. Therefore, it is widely used in aerospace, communication power supply, automotive electronics, electronic equipment, power control and other fields. These module power supplies usually require a wide operating power range (36 V to 75 V) and high output power (can provide all-brick module power up to 700W), and the power density is very high, cooling design is a big problem.
For example, the half brick output power of 200W module power supply, its conversion efficiency is 89%, then 24.7W of electrical energy into heat, if there is no cooling measures, half brick module power supply may be damaged due to overheating. Therefore, in the design of high-power module power supply, appropriate heat dissipation design is more and more important.
Power structure of DC-DC power module:
The key components of the power structure of DC-DC power module are: pulse width modulator, optocoupler, VDMOS and Schottky diode.
The selection of power modules should be based on the following four points:
1, the use of mature power supply topology
The design of the power module is based on the mature power topology. These topologies have been tested over time and are mature and reliable.
2, high efficiency within the full load range
High efficiency means lower power loss and lower temperature rise, which can effectively improve reliability. In practical applications, the power supply will choose a certain degree of downscaling design, especially in today’s load IC power consumption is getting lower and lower, most of the time the power supply may work under light load conditions. Therefore, high efficiency over the entire load range is a key parameter for power system reliability, but it is often overlooked by power supply manufacturers.
3, limit temperature characteristics
The geographical area where the power module is applied is very wide and may have tropical climate and cold weather similar to Russian winter. Therefore, the minimum operating temperature range of DC-DC module is required to be -40 degrees to 85 degrees. The final temperature test is the most reliable way to verify this. The reliability of the power module, such as high temperature aging, high temperature and low temperature live operation performance test, high temperature and low temperature cycle impact test and long time high temperature and high humidity test, therefore, whether this test equipment has become the basis of judging whether the power manufacturer is a copycat manufacturer.
4, high isolation, low isolation capacitance
Medical products require extremely low leakage currents, while power electronics require as little parasitic capacitance as possible between primary and secondary. Both industries generally require the highest possible isolation voltage withstand and the lowest possible isolation capacitance to reduce the impact of common-mode interference on the system. For medical or power electronics applications, 1-2W DC-DCs are recommended to use a power module with an isolation capacitor less than 10pF, and a wide voltage product with a power module less than 150pF.
Précédent: Comment choisir un dégagement de qualité et des fabricants de modules de puissance fiables?
les informations pertinentes
-
2023-11-12
Exploring the Advantages of a Modular PC Power Supply
In the world of computer hardware, power supply units (PSUs) are an essential component that often goes overlooked. However, choosing the right PSU can have a significant impact on the performance and longevity of your computer. One option that has gained popularity in recent years is the modular power supply. In this article, we will explore the advantages of a modular PC power supply and why it might be the right choice for your next build. To understand the advantages of a modular power supply, it is important to first understand the difference between modular and non-modular PSUs. Traditional non-modular power supplies come with a fixed set of cables that are permanently attached to the unit. This means that all...
Voir les détails -
2023-6-3
12V 15A AC to DC Converter: Transforming Alternating Current into Direct Current
In today's world, electricity is an essential part of our daily lives. We use it to power our homes, workplaces, and even our vehicles. However, the electrical power that we receive from the grid is in the form of alternating current (AC), which is not suitable for many devices that require direct current (DC) to operate. This is where a 12V 15A AC to DC converter comes in. As the name suggests, this device converts AC power into DC power, making it possible to power DC devices from an AC source. The process of converting AC power to DC power involves several stages. The first stage is rectification, which involves converting the AC signal into a pulsating DC signal. This...
Voir les détails -
2023-5-8
Designing an AC-DC Converter Circuit: A Step-by-Step Guide
Introduction An AC-DC converter circuit is an electrical circuit that is used to convert alternating current (AC) to direct current (DC) voltage. This converter circuit is commonly used in electronic devices such as computers, televisions, and audio equipment. The AC-DC converter circuit design can be complex, and it requires a good understanding of electronic circuits, components, and their properties. In this article, we will provide a step-by-step guide to designing an AC-DC converter circuit. Step 1: Determine the Required Voltage and Current The first step in designing an AC-DC converter circuit is to determine the required voltage and current for your application. This will depend on the electronic device that you are designing the circuit for. For example, a computer...
Voir les détails -
2023-7-13
Introduction to Bidirectional Converters: A Versatile Solution for Language Conversion
Language conversion has become increasingly important in our globalized world, where communication across different languages is a necessity. With the advancement of technology, bidirectional converters have emerged as a versatile solution for seamless language conversion. This article aims to provide an overview of bidirectional converters, their applications, and the benefits they offer. What are Bidirectional Converters? Bidirectional converters are software tools or algorithms used to convert text or speech from one language to another and vice versa. Unlike traditional one-way translation tools, bidirectional converters offer the ability to translate content in both directions. This means that content can be translated from English to French and then back from French to English, ensuring accurate and coherent communication. Applications of Bidirectional Converters...
Voir les détails -
2023-8-26
The Electric Power Series: Harnessing Energy for a Sustainable Future
In recent years, the world has witnessed a growing concern about the future of our planet. The increasing threat of climate change and the depletion of natural resources have pushed us to explore alternative sources of energy. In this regard, the electric power series has emerged as a promising solution for a sustainable future. The electric power series refers to a range of technologies that generate electricity using renewable sources such as solar, wind, hydropower, and geothermal energy. These technologies are considered sustainable because they have minimal impact on the environment and can be replenished naturally. Moreover, they do not contribute to greenhouse gas emissions, which are the leading cause of global warming. Solar power is one of the most...
Voir les détails -
2023-6-13
Efficient AC DC Power Supply with PFC Technology
Power supply technology has come a long way since the early days of electronics. One of the biggest advancements in power supply technology has been the development of Power Factor Correction (PFC) technology. PFC technology has revolutionized the way that power is delivered to electronic devices, making power supplies more efficient, reliable, and cost-effective. In this article, we will discuss how PFC technology works and how it has improved the efficiency of AC DC power supplies. What is PFC Technology? Power Factor Correction technology is a method of correcting the power factor in an AC circuit. The power factor is a ratio of the real power (watts) to the apparent power (volt-amperes) of a circuit, and it indicates how efficient...
Voir les détails