Wie wählt man Qualitätsfreigabe und zuverlässige Hersteller von Leistungsmodulen?
Heim - Bloggen - Unternehmens Nachrichten - So wählen Sie eine DC-DC-Wandlerfabrik aus, wie Sie einen hochwertigen DC-DC-Wandler auswählen

So wählen Sie eine DC-DC-Wandlerfabrik aus, wie Sie einen hochwertigen DC-DC-Wandler auswählen

Autor: ZYG Leistungsmodul Time: 2022-9-16

What is a DC-DC converter?
A DC-DC converter, also known as a DC-DC converter or DC transformer, is a circuit or electromechanical device that converts electrical energy. It can convert direct current (DC) power to DC power (or approximate DC) of different voltages. Its power ranges from very low (small batteries) to very high (high voltage power transfer). The output voltage of some DC-DC converters has the same reference point as the input voltage, while the output voltage of some DC-DC converters is isolated from the input voltage.

 

 

DC-DC Converter Inductor Selection

The process of selecting an inductor for a DC-DC converter depends on many parameters. Depending on the power levels involved, these inductors can be quite large and may need to be designed for your system. In addition to the required area, the following specifications are also important. You need to consider the choice of DC-DC converter electrical sensors:

Rated current and coil resistance. The coil itself will have some DC resistance, which will generate heat and reduce some voltage across the inductance. Coil resistance should be as low as possible to prevent power loss. Also, the current rating will depend on the physical size of the inductor package; winding sensors are used for high power converters, while foil electric motors can be used for low power converters.

 

 

saturation current. Ferrite sensors will have some saturation current, which will saturate the core than saturation current sensors. This will cause the next switching cycle to lag. The inductor should be chosen so that the saturation current is greater than the maximum current required by the system.

inductance and frequency. All components have parasitic effects. Parasitic capacitances between windings and coil resistances can cause the system to self-resonate. In fact, the self-resonant frequency of the inductor is usually very high, so it doesn’t matter unless you intend to use a PWM signal with a very fast edge rate and a frequency around MHz.

DC DC Converter Inductor Selection and Inductor Type

Finally, and least important is the inductance value. The required inductor value depends on the topology you use, as this will determine the function the DC-DC converter needs to perform.

relevante Information

  • 2023-4-18

    Unterscheidung zwischen AC- und DC-Netzteilen

    Distinguishing between AC and DC power supplies is important in understanding how electrical devices are powered. AC and DC are two different types of electrical current that have different characteristics and are used in different ways. This article will explain the differences between AC and DC power supplies and how they are used. AC power supplies AC stands for alternating current, which means that the flow of electricity alternates between positive and negative values. This type of current is generated by power plants and is distributed through power lines to homes and businesses. AC power supplies are used to power a wide range of electrical devices, including home appliances, computers, and industrial equipment. One of the benefits of AC power...

    Einzelheiten anzeigen
  • 2023-11-16

    Introducing the Innovative Concept of Modular PC Power Supply

    In the world of technology, advancements are constantly being made to enhance user experience and improve efficiency. One such innovation in the field of computer hardware is the concept of a modular power supply for personal computers. This groundbreaking concept offers users the flexibility to customize their power supply unit according to their specific needs, resulting in a more efficient and organized PC setup. Traditionally, power supply units (PSUs) in personal computers come in a fixed configuration, with a fixed number of cables and connectors. This rigid design often leads to cable clutter and limited flexibility when it comes to adding or removing components. However, with the introduction of modular power supplies, this problem has been effectively addressed. A modular...

    Einzelheiten anzeigen
  • 2023-4-15

    How an AC-DC Converter Works

    An AC-DC converter is an electrical device that converts alternating current (AC) power to direct current (DC) power. This is a critical component in many electronic devices, as most electronics require DC power to operate, but AC power is typically what is delivered from wall outlets. The process of converting AC power to DC power involves a few key components. The first component is a transformer, which steps down the voltage of the incoming AC power to a lower level. This is necessary because many electronics require lower-voltage DC power to operate. After the transformer steps down the voltage, the AC power is then rectified. This means that the AC power is converted to pulsating DC power. This pulsating DC...

    Einzelheiten anzeigen
  • 2023-5-5

    Designing an AC-DC Converter Circuit

    Introduction An AC-DC converter circuit is a device that converts an alternating current (AC) source to a direct current (DC) source. This conversion is important because many electronic devices require a DC power source to operate. Designing an AC-DC Converter Circuit The first step in designing an AC-DC converter circuit is to determine the specifications of the circuit. This includes the input voltage range, the output voltage and current requirements, and the efficiency of the circuit. Next, the type of AC-DC converter circuit to be used must be chosen. There are several types of AC-DC converter circuits including half-wave rectifiers, full-wave rectifiers, and bridge rectifiers. Each type has its advantages and disadvantages, so the choice depends on the specific application....

    Einzelheiten anzeigen
  • 2023-8-28

    ZP Series AC DC Converter: Unleashing Efficient Power Conversion

    Introduction: Where energy efficiency and sustainability are of paramount importance, finding ways to convert power efficiently has become crucial. The ZP Series AC DC Converter is at the forefront of this technological innovation, offering a reliable and efficient solution for power conversion needs. This article will delve into the features and benefits of the ZP Series, highlighting its ability to unleash efficient power conversion. Efficiency and Reliability: One of the key features of the ZP Series AC DC Converter is its exceptional efficiency. With a conversion efficiency of up to 98%, it ensures minimal energy loss during the power conversion process. This high efficiency not only saves energy but also reduces costs and environmental impact. The ZP Series is designed...

    Einzelheiten anzeigen
  • 2023-9-21

    Enhance Your PC Performance with a Modular Power Supply

    A modular power supply is a key component in any computer system, responsible for providing stable and efficient power to all the components. Power supply units (PSUs) come in various types, including non-modular, semi-modular, and modular. Among these, a modular power supply is gaining popularity due to its versatility and ability to enhance PC performance. In this article, we will explore the benefits of using a modular power supply and why it is an excellent investment for your computer system. Firstly, let's understand what exactly a modular power supply is. Unlike non-modular PSUs, which have a fixed set of cables permanently attached to the unit, modular PSUs allow users to connect only the cables they need. This means that unnecessary...

    Einzelheiten anzeigen

Über 6000 Optionen, Stromversorgungslösungen aus einer Hand